Forum Replies Created
-
AuthorPosts
-
FREDDY SANDOVALParticipant
Sold, please delete.
FREDDY SANDOVALParticipantSold
FREDDY SANDOVALParticipantSold, please delete.
FREDDY SANDOVALParticipantSold
FREDDY SANDOVALParticipantSold
FREDDY SANDOVALParticipantSold
FREDDY SANDOVALParticipantLoosen up side pods, rear bumper, if you have rear torsion bar remove it, remove one seat strut, and go higher on tire pressure. Leave the caster at max.
Where is your seat at from axle to lip?
Where is your front and rear track at?
FREDDY SANDOVALParticipantJust have some one put it on the table and do it for you
Most table guys will charge you anywhere from $100, $150 to $200
And it will work just fine
Save all your time, frustration, tooling expenses while supporting a local karting shop.
I know most table guys will show up at most major events to offer their services, as there are lots of bent chassis during the race.
But if this is not doable then build a tool that will attach to the yoke in place of the spindle with threaded holes at top and bottom, make sure the spacers fit up on top of the yokes, where the camber pills go, then put bolts and washers top and bottom, tighten them up.
Then weld a very strong handle in the middle for you to pry it down with.
Good luck, and I hope I didn’t confuse you too much. FastFreddy.
FREDDY SANDOVALParticipantYeah, that was totally non intentional, looks like they had a good battle going on, passing each other back and forth before your Son got there.
This is the typical factor that takes place when 2 karts on the lead are battling for position, they start losing time and the kart behind them benefits from all that fighting they’re doing.
And yes, he was trying to recover and cross the other driver when your Son got there. Good driving from all of them by the way.
April 14, 2016 at 9:49 pm in reply to: WTB: gear shift lever for SKM/Italkart shifter chassis #64440FREDDY SANDOVALParticipantI found a few leads for you, hope this helps?
FREDDY SANDOVALParticipantSold, Thanks Brad
FREDDY SANDOVALParticipantDan
Check your PM
I have 2 options for the Mag wheels you want.
FREDDY SANDOVALParticipantDaniel
Check your PM
FREDDY SANDOVALParticipantSold, please delete
FREDDY SANDOVALParticipantSold
FREDDY SANDOVALParticipantAndy
We have a very nice big aluminum radiator we ran on our stock moto
$250 shipped to your door
FREDDY SANDOVALParticipantDennis
I don’t know if this is what you’re looking for, but we have an older 2011 FA Kart, same as Tony Kart, Kosmic and all the OTK stuff
We mainly used it at the club level for 2 years with Yamaha KT100, and ran once at the California State Championship with KPV4, but the chassis is designed for TAG 125cc and 100cc.
The beautiful blue color is not so pretty anymore, and may need a good powdercoating if you want it to look nice, otherwise it is still a good fighting chassis with caracter, and the normal wear and tear flat spost and scratches at the bottom.
$700.00 plus shipping anywhere in the US for under $200 bucks
FREDDY SANDOVALParticipantKart sold, please delete. Thanks Austin and EKN
FREDDY SANDOVALParticipantPlease delete kart sold, Thanks Eric and EKN
FREDDY SANDOVALParticipantSold, Thanks Eric and EKN
FREDDY SANDOVALParticipantKart sold, Please delete. Thanks Austin and EKN
FREDDY SANDOVALParticipantSold, Thanks Eric and EKN
FREDDY SANDOVALParticipantPlease delete, kart sold. Thanks Eric and EKN
FREDDY SANDOVALParticipantKart sold, Please delete. Thanks Austin and EKN
FREDDY SANDOVALParticipantDelete
-
AuthorPosts
Archives
