Bryan Williams

Forum Replies Created

Viewing 20 posts - 51 through 70 (of 70 total)
1 2 3
  • Author
    Posts
  • May 4, 2014 at 5:21 pm in reply to: is my spindle no good? #26847
    Bryan Williams
    Participant

    May 2, 2014 at 4:53 pm in reply to: Margay identification #26707
    Bryan Williams
    Participant

    http://margay.com/what-kart-do-i-have.html

    March 23, 2014 at 5:25 pm in reply to: sr-y pipe flex length #24359
    Bryan Williams
    Participant

    so the shorter the flex length the more top end you will produce?

    March 16, 2014 at 4:36 pm in reply to: starter nut #23922
    Bryan Williams
    Participant

    I have looked for some sort of spanner wrench like the make for a horstman dry clutch with no results. I have a wet clutch puller but it requires the starter nut to be removed to pill the clutch. Could I hurt anything if I tried a larger air impact vs my 18v dewalt impact?

    Thanks

    March 16, 2014 at 3:17 pm in reply to: starter nut #23915
    Bryan Williams
    Participant

    ok. im semi new to this but have taken a few different clutches and starter nuts on and off. Is it normal to have Loctite on the starter nut? The lady I bought the setup from new almost nothing so Im sure calling and asking if there was Loctite applied would not help.

    March 16, 2014 at 2:31 pm in reply to: sr-y pipe flex length #23910
    Bryan Williams
    Participant

    mine is 6 1/4 inch. it was cut by the local kart guy to make it legal for our local track. So not sure if that’s a standard or just our tracks thing. Also I thing the longer it is the more power you get. I am semi new also so I wouldn’t take my word for gospel, its just what I have.

    also fyi I am running a kt100. not sure if that pipe goes on other motors also.

    March 5, 2014 at 11:51 am in reply to: 3 disk dxl wet clutch #23292
    Bryan Williams
    Participant

    I talked to one of the guys at horstman and he said it sounds like I’m doing everything right and have good endplay which he said really the most important part. He said put it all the way together fill it with oil and start it up. Then see how it feels with the motor off.

    March 5, 2014 at 8:01 am in reply to: 3 disk dxl wet clutch #23274
    Bryan Williams
    Participant

    The friction is before I even put the out side cover on and fill with oil. I did notice if I just barely finger tight the starter nut it spins good. But no where near the 350 inch pounds. Not sure on the other measurements, I need to go buy a caliper today after work.

    February 13, 2014 at 5:53 pm in reply to: Axles, belt drive parts, rain tires, rims #21988
    Bryan Williams
    Participant

    Are the axles pretty straight and would you sell 2 for 80 shipped to 93314?

    February 3, 2014 at 7:25 pm in reply to: repair a bent axle? #20932
    Bryan Williams
    Participant

    Yeah I talked to the guy that runs the local kart shop here and he said from what he has seen margays seem to run faster on a 40mm axle anyways. So that’s what I’m sticking with. Thanks for the responses.

    February 3, 2014 at 8:30 am in reply to: repair a bent axle? #20883
    Bryan Williams
    Participant

    Thanks for the info. I have been thinking about going to a 50mm. I’m pretty new to the sport still, what are the benefits of going to a 50mm?

    January 19, 2014 at 3:48 pm in reply to: Yamaha KT100 for sale #19866
    Bryan Williams
    Participant

    Got them. Damm junk box ate it.

    January 19, 2014 at 3:30 pm in reply to: Yamaha KT100 for sale #19864
    Bryan Williams
    Participant

    Didn’t get them.

    January 19, 2014 at 3:02 pm in reply to: Yamaha KT100 for sale #19861
    Bryan Williams
    Participant

    Tried emailing you but would not work. How much shipped to 93314. Ups preferred no USPS. Bryan34w@hot mail.com. any pics.?

     

    December 14, 2013 at 11:46 am in reply to: sold..thanks #17790
    Bryan Williams
    Participant

    Sent email

    But just in case what else is needed to complete a 2 disk wet clutch. I know basic question but I’m a new.

    October 15, 2013 at 8:41 pm in reply to: to tight? #12961
    Bryan Williams
    Participant

    Thanks for the advice. I’m 5’10 200. I run in a 360 class so I have no added weight. My sear is about 2 inch in front of my rear axle and the top is about 8 above. I will try narrowing the front also.

    September 10, 2013 at 6:06 pm in reply to: Starting line #9568
    Bryan Williams
    Participant

    Thanks guys for the help. Like I said I’m still new and learning this sport but love going fast and am very competitive.

    September 10, 2013 at 9:20 am in reply to: Starting line #9529
    Bryan Williams
    Participant

    I’ve noticed both strategies from the races I’ve watched. The first corner seems to be a magnet for spin outs and the guys that hang back bypass all that.

    August 27, 2013 at 8:02 pm in reply to: Racing Suits For Sale #8232
    Bryan Williams
    Participant

    Pm sent

    August 27, 2013 at 3:22 pm in reply to: Garage Sale Galore Free Tyres #8209
    Bryan Williams
    Participant

    What size are the rain tires. Do you have any wheels?

  • Author
    Posts
Viewing 20 posts - 51 through 70 (of 70 total)
1 2 3