Forum Replies Created

Viewing 24 reply threads
1 2
  • Author
    Posts
    • February 16, 2018 at 9:23 am #91248
      CLIFF BRYANT
      Participant

      Are these rims still available???

    • March 18, 2017 at 2:11 pm #79423
      CLIFF BRYANT
      Participant

      For parts I like Comet Kart Sales. Good people and great service. But there are a lot of good shops out there.

    • January 2, 2017 at 2:33 pm #76167
      CLIFF BRYANT
      Participant

      Maybe this will work. https://www.ebay.com/itm/262789734053

    • June 24, 2016 at 4:39 pm #67719
      CLIFF BRYANT
      Participant

      Try this guy. Maybe he can help you out. https://www.facebook.com/TJR-Race-Fab-961664147260228/

    • June 21, 2016 at 6:15 am #67537
      CLIFF BRYANT
      Participant

      Bump to the top.

    • June 13, 2016 at 6:44 am #67175
      CLIFF BRYANT
      Participant

      Gregory you have a PM

    • May 23, 2015 at 7:13 am #48758
      CLIFF BRYANT
      Participant

      WOW!! That is a pretty impressive collection. Just a good example of what’s still out there in old buildings and garages. Agreed finding a buyer for it all in one lump some by be difficult.

    • May 20, 2015 at 6:31 pm #48591
      CLIFF BRYANT
      Participant

      John back on 3-1-14. EKN member Joseph Bath had a odenthal Kt100 mount for sale in the classified parts section on here. Not sure if he still has it. No one makes mounts for the (125mm Tony//Kart spacing) that I can find any more. But you can find them on EBay every now and then. Since there’s no room to mount the sprocket on the inside you could always go to a jack shaft set up with a 4cycle. You could also install a short length of 32mm tubing alongside the tube that has the right side seat mount attached to it. This will now give you the 92mm International Frame spacing. Then you should be able to use any off-the-shelf mount you need. I hope this helps and makes sense. I to have a Extream Chassis. I know what you are up against.

    • May 12, 2015 at 9:46 pm #48090
      CLIFF BRYANT
      Participant

      Rear axle and/or brakes included? Thanks…

    • April 25, 2015 at 10:41 am #46853
      CLIFF BRYANT
      Participant

      Sorry to hear of the loss of your mom. May God bring peace to your mind and heart.

    • December 1, 2014 at 6:49 pm #38096
      CLIFF BRYANT
      Participant

      This might be what your looking for. Check out Comet kart sales. Under chassis parts/Weld on parts. Nerf bar weld on spud.

    • July 25, 2014 at 3:23 pm #30875
      CLIFF BRYANT
      Participant

      There’s a couple listed on eBay now. If you’re patient and shop around you can find one a lot cheaper then you can make one.

    • July 25, 2014 at 3:18 pm #30874
      CLIFF BRYANT
      Participant

      Pm sent

    • July 25, 2014 at 10:59 am #30854
      CLIFF BRYANT
      Participant

      19 hours and not a single reply. Posted on Bobs4cyl And got 2 replies in less than 19 mins. Sad. Don’t know what’s happened sense the change, but it don’t seam to be working……

    • June 17, 2014 at 4:57 pm #29076
      CLIFF BRYANT
      Participant

      Used one on eBay now. Not much time left.

    • June 17, 2014 at 4:49 pm #29075
      CLIFF BRYANT
      Participant

      Steen. Thanks for the input. I have other hubs of different Manufactures that all fit my Tony/Kart rims. These were like new and I thought there were a good deal. I didn’t think they would made another bolt circle that close. I could file out the holes in my rims, but I believe I will remove the studs and bolts and retire them. Oh well. And yes it probably is better to buy every thing NEW and take care off it. But I work on trucks for a living. Not planes. Thanks guys…….

    • June 16, 2014 at 3:45 pm #29013
      CLIFF BRYANT
      Participant

      I was just wondering, because I bought two hubs off eBay and they seem to be about 1 mm bigger bolt circle then my Tony/Kart rims. I guess they must be fudged up and I reckon that’s why I got a good deal off eBay.

    • June 12, 2014 at 6:02 pm #28867
      CLIFF BRYANT
      Participant

      Hay I got it to open on my PC. Read it and cleared it out. Maybe will figure this new site out if we stick to it. LOL. Thanks for the help Tony.

    • June 11, 2014 at 7:15 pm #28800
      CLIFF BRYANT
      Participant

      PRD Fireball on eBay now.

    • June 11, 2014 at 7:08 pm #28797
      CLIFF BRYANT
      Participant

      If you can’t weld it yourself, I would recommend getting someone to tig weld it. Someone who is good. It does a much better job on the thin wall tubbing that kart chassis are made from. I have often wondered why kart manufacturers don’t use a clamp on seat mount that you could adjust and move/replace. I know they make them. Doesn’t make any sense to me why you Would spend a 150 to 350 on a seat and drill It full of holes. JMO

    • June 11, 2014 at 6:49 pm #28794
      CLIFF BRYANT
      Participant

      I have the same problem. I have had one notification for quite sometime. Now I have two notifications. I cannot figure out how to open it or read it either. I’m trying to do this with an iPhone I don’t know if that makes a difference or not.

    • June 6, 2014 at 5:43 am #28490
      CLIFF BRYANT
      Participant

      Email sent

    • May 28, 2014 at 5:06 pm #28095
      CLIFF BRYANT
      Participant

      Glad to here your son is home. Hope all is well.

    • May 17, 2014 at 9:31 am #27606
      CLIFF BRYANT
      Participant

      I have a Odenthal a GEM and a nos Burris. All 3 are kt 100 with 3rd bearing support. The Odenthal and Burris are international rail and the GEM will do both I think.

    • May 14, 2014 at 6:13 pm #27496
      CLIFF BRYANT
      Participant

      Thanks Daniel, for the info. I am new to karting and was wondering if there was any thing like that going on around here. (I live in Martinsville). I would like to check it out, maybe in Danville at the airport. Thanks

  • Author
    Posts
Viewing 24 reply threads
1 2