Craig Whitfield

Forum Replies Created

Viewing 18 posts - 1 through 18 (of 18 total)
  • Author
    Posts
  • December 22, 2014 at 12:54 am in reply to: OTK MXC Wheels. #39236
    Craig Whitfield
    Participant

    These were used in kz gearbox

    December 18, 2014 at 8:02 pm in reply to: OTK MXC Wheels. #39130
    Craig Whitfield
    Participant

    $500 anyone ?

    Buyer pays shipping.

    December 15, 2014 at 4:22 pm in reply to: 2014 Tonykart Evk stock shifter #38956
    Craig Whitfield
    Participant

    Sold

    December 13, 2014 at 5:51 pm in reply to: 2014 Tonykart Evk stock shifter #38844
    Craig Whitfield
    Participant

    Sold

    December 8, 2014 at 8:21 pm in reply to: 2014 Tonykart Evk stock shifter #38611
    Craig Whitfield
    Participant

    Sold

    October 3, 2014 at 6:25 pm in reply to: 2014 Tonykart Evk shifter chassis #34846
    Craig Whitfield
    Participant

    $4000 bargain especially with mxc wheels and spares etc

    September 13, 2014 at 1:21 pm in reply to: 2014 Tonykart Evk shifter with 01 swedetech stock engine!!! #33593
    Craig Whitfield
    Participant

    Price drop $8500 I’m heading back home so it must sell or I’ll be taking a souvenir with me.

    September 5, 2014 at 11:18 pm in reply to: 2014 Tonykart Evk shifter with 01 swedetech stock engine!!! #33203
    Craig Whitfield
    Participant

    Come on someone must want it?

    I’m selling everything here including a full tool cheat with lots of spares, this is a bargain. Someone make me a sensible offer. I’m heading home soon so she needs to go.

    July 2, 2014 at 5:06 pm in reply to: chain length, does it matter? #29716
    Craig Whitfield
    Participant

    I’m quite surprised no one has answered this one.

    With the shifter kart you can only get 60link 428 chains but correct me if I’m wrong. Obviously with gearing bigger or smaller you have to shorten the chain or use maximum length.

    If a kart seat 10mm further forward or back can make a difference I’m sure a engine 10mm further forward or back can also make a difference.  Maybe I answered my own question but who knows. It’s got me thinking.

    Anyway I will try a 59 link chain on Saturday, it’s 59 because my engine stop was at max length.

     

    Craig.

    June 24, 2014 at 2:27 pm in reply to: Tonykart rear brakes wont self adjust #29391
    Craig Whitfield
    Participant

    Guys it’s fixed. I removed the stop at the pedal to allow the arm to go fully back like steen said and I then noticed the left side moving then eventually the right side moved to.

    Thanks guys I really appreciate the time you took to answer the questions.

    Now I just need to even them out.

    Thanks again

    Craig whitfield

    June 24, 2014 at 11:28 am in reply to: Tonykart rear brakes wont self adjust #29388
    Craig Whitfield
    Participant

    I removed the reservoir caps yes but not the rubber seals??? The rubber seals on the lids or where the actual bleeding tool screws in?

    I hope it’s something stupid I’m doing and is an easy fix. The pistons on the rear definitely seem vacuum locked because both always return to same position.

    June 10, 2014 at 2:05 pm in reply to: Tonykart setup at DKC #28710
    Craig Whitfield
    Participant

    The track was very strange on Saturday.

    I definitely went the opposite way and put to much front into the kart thinking it would help.

    I’m heading back in a few weeks so will give it another shot.  I remember the first time I went I had to much grip so I will go back to the narrow front.

    I put the front way to wide on one run on sunday and it was 1 second slower.

    Thanks TJ

    May 23, 2014 at 8:08 pm in reply to: OTK seat VS Tillet #27909
    Craig Whitfield
    Participant

    Yea Gary the otk seats are terrible and I’m sure the tolerance is plus or minus 50mm because my size 3 is not a size 3.

    Padded the hell out of it. Maybe the Tillet will be better quality.

    May 23, 2014 at 10:27 am in reply to: OTK seat VS Tillet #27896
    Craig Whitfield
    Participant

    I was advised to use a t11t ? I do not understand the otk sizing. After measuring my seat the otk size 3 is not the measurements on the otk chart.

    I ordered a m/s in the Tillet and hoping it doesn’t destroy the handling

    April 19, 2014 at 2:55 pm in reply to: Tonykart 14 EVK seat location #25934
    Craig Whitfield
    Participant

    Hi mark.

    Thanks for the reply. I tried the seat today and kart felt totally different.

     

    If you want to loosen up the rear do people go hard on axles or soft? I’m sure it’s the opposite with Tonykart?  Very new to otk stuff.

    Thanks

    Craig

    March 26, 2014 at 10:05 pm in reply to: OTK MXC wheels #24566
    Craig Whitfield
    Participant

    TJ

    I went ahead and bought a set. I’m new to the tonykart so just getting familiar with it.

    March 24, 2014 at 8:04 pm in reply to: Help needed – Extending Pedals 2013 Kosmic Lynx? #24460
    Craig Whitfield
    Participant

    I second this. I to need to move the pedals forward.

    Not the best design from OTK as regards to adjusting them for us stumpy leg folks.

     

    I’m a cnc machinist so i might manufacture some of my own.

     

    Craig

    March 18, 2014 at 4:23 pm in reply to: Tonykart EVK stock moto setup HELP #24053
    Craig Whitfield
    Participant

    Thanks guys I appreciate the help.

    I was struggling a little when the tires were little worn I wanted a little more front bite on turn in?

    Apart from that the Tonykart is a brilliant kart.

  • Author
    Posts
Viewing 18 posts - 1 through 18 (of 18 total)