Forum Replies Created

Viewing 5 posts - 76 through 80 (of 80 total)
  • Author
    Posts
  • in reply to: Electric Kart Stands #6853
    Ace Rossi
    Participant

    Chris, I too am looking at buying a lift! Been looking at the kart lift prop and been saving up for it. If you decide on the same, maybe we can get a better deal if we order together and get two at once!

     

    in reply to: Florida master shifter series #6850
    Ace Rossi
    Participant

    Marc, bring it to OGP on Sept 7 for the first fall series race!

    would be nice to finally meet you!

    in reply to: Central Florida baseline Stock Honda carb setting #5590
    Ace Rossi
    Participant

    Don’t know what happened but this was straight from Swedetechs site:

    no pump gas and use VP MS98 mixed at 24:1

    a lot of recreational racers WILL buy pump gas out of convenience!

    this new site is definitely not smart phone useable!

     

    in reply to: Central Florida baseline Stock Honda carb setting #5588
    Ace Rossi
    Participant

    From the Swedetech site:
    <p style=”text-align: -webkit-auto;”><span style=”background-color: rgba(255, 255, 255, 0);”>Oil – Motul Kart Grand Prix or Maxima 927 – mixed at 24:1</span></p>
    <p style=”text-align: -webkit-auto;”><span style=”background-color: rgba(255, 255, 255, 0);”>Fuel – VP MS98 – Do Not Use Pump Fuel</span></p>
    <p style=”text-align: -webkit-auto;”><span style=”background-color: rgba(255, 255, 255, 0);”>Transmission Oil – Motul Trans Oil 10w30 or Motul Trans Oil Expert 10w40</span></p>

    <h1 style=”text-align: -webkit-auto; padding-top: 30px; margin: 0px;”><span style=”font-size: small;”><span style=”background-color: rgba(255, 255, 255, 0);”>Jetting</span></span></h1>
    <h2 style=”text-align: -webkit-auto; margin: 30px 0px 0px;”><span style=”font-size: small;”><span style=”background-color: rgba(255, 255, 255, 0);”>Keihin 38mm PWM</span></span></h2>
    <p style=”text-align: -webkit-auto;”><span style=”background-color: rgba(255, 255, 255, 0);”>160-180 main (center of the carb, 6mm hex )      Main jet supplies fuel from ½ throttle to full throttle</span></p>
    <p style=”text-align: -webkit-auto;”><span style=”background-color: rgba(255, 255, 255, 0);”>48-62 pilot (next to main jet, use 5mm flat screwdriver to remove)          Pilot jet supplies fuel from 0 – ¼ throttle</span></p>
    <p style=”text-align: -webkit-auto;”><span style=”background-color: rgba(255, 255, 255, 0);”>DGK,DGJ, or DGH needle – 3<sup>rd</sup> from top.  Experiment with 4<sup>th</sup> & 2<sup>nd</sup> clip from top.               Needle regulates fuel from 1/8 throttle to ¾ throttle</span></p>
    <p style=”text-align: -webkit-auto;”><span style=”background-color: rgba(255, 255, 255, 0);”>Air Screw (side of carburetor body, above fuel inlet) – 1 Turn      Air Screw regulates air from 0 – 1/8 throttle.  Turning the air screw in will reduce air through circuit, effectively, increasing the fuel to air ratio.</span></p>
    <p style=”text-align: -webkit-auto;”></p>
    <p style=”text-align: -webkit-auto;”></p>
     

    in reply to: Central Florida baseline Stock Honda carb setting #5524
    Ace Rossi
    Participant

    Jason at Swedetech advised me to NEVER run pump gas. Always use VP ms98 mixed with ONLY 6 ozs of Motul oil! I’ve never had a problem, yet!

    As for jetting? It changes with the weather! Matter of fact, it probably changed since I started this reply! Just sayin’!

    By the way Gene, where are you located in central Florida?

     

Viewing 5 posts - 76 through 80 (of 80 total)