| View previous topic :: View next topic |
| Author |
Message |
Sean Riddell
Joined: 28 Jun 2012
Posts: 4
|
 Posted: Tue Jul 03, 2012 3:35 pm Post subject: New TaG Kart |
 |
|
Hi,
just picked this TaG kart with a Leopard RL engine up yesterday, and wondering if anyone could help I.D. the chassis...
 |
|
| Back to top |
|
 |
Oscar Biondi
Joined: 27 Sep 2011
Posts: 226
Location: United States, California, Carmichael
|
| Posted: Tue Jul 03, 2012 6:32 pm Post subject: |
|
|
I'm going to guess it's an Italsistem chassis  Nevermind, Italsistem only made engines. http://www.italsistem.com/storia-eng.htm
Last edited by Oscar Biondi on Tue Jul 03, 2012 7:18 pm, edited 1 time in total |
|
| Back to top |
|
|
TJ Koyen
Joined: 03 Oct 2004
Posts: 1459
|
| Posted: Tue Jul 03, 2012 6:45 pm Post subject: |
|
|
If you take a look at the rear crossbar under the seat, there should be a homologation plate on there with some numbers. If you could get a pic of that, someone could give you better info on the chassis.
_________________
T.J. Koyen
OKTANE VISUAL - Custom Helmet Paint & Graphic Design
www.oktanevisual.com
www.facebook.com/oktanevisual
--------------------------
DB Motorsports
Exprit/Leopard |
|
| Back to top |
|
|
Sean Riddell
Joined: 28 Jun 2012
Posts: 4
|
| Posted: Tue Jul 03, 2012 7:44 pm Post subject: |
|
|
I couldn't find anything on the frame at all. The only numbers I could find are on the front and side bumpers.....19/CA/08.
TonyKart is engraved on the gas/brake pedals but this name is engraved on the floorpan, bumpers and on the steering wheel,
 |
|
| Back to top |
|
|
Oscar Biondi
Joined: 27 Sep 2011
Posts: 226
Location: United States, California, Carmichael
|
| Posted: Tue Jul 03, 2012 7:53 pm Post subject: |
|
|
Italcorse. Look at the link I posted above. Looks like italsistem motors started the italcorse line of chassis in 97.
Any marks on the brake master cylinder, brake caliper, rear axle bearings? |
|
| Back to top |
|
|
Brian McHattie
Joined: 28 Jan 2002
Posts: 386
|
| Posted: Wed Jul 04, 2012 12:58 pm Post subject: |
|
|
Its an ItalCorse It- series chassis. If it is all 32mm tubing its an IT-13
These were built by Achille Parilla to go along with his ItalSistem engines.
_________________
Brian McHattie
www.dbmotorsportsonline.com
all your graphic needs |
|
| Back to top |
|
|
Sean Riddell
Joined: 28 Jun 2012
Posts: 4
|
| Posted: Wed Jul 04, 2012 2:52 pm Post subject: |
|
|
Thanks guys!
Hopefully didn't bite off more than I can chew with this thing!
Needs a bit of work as it was sitting for a few years.
Spent all night pulling the brakes apart after trying to bleed them only to find the cup seals leaking due to the inside being all corroded. Little steel wool=good as new.
Needs a starter batt.
Need to replace the water pump O-rings,thinking silicone?
New batts in the Mycron, some fresh 100ll/castor927 and hopefully test her out next week!!
Thanks again guys!!!
Brian, looks like its 30mm measured across the tubes... |
|
| Back to top |
|
|
Brian McHattie
Joined: 28 Jan 2002
Posts: 386
|
|
| Back to top |
|
|
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Login to check your private messages
Login
